A label wrapped around a cylinder covers its curved side, not its circular ends. Find the lateral area by multiplying the base circumference by the height, and see how a 16-inch diameter and 20-inch height give an area of 320π square inches.

Multiple Choice

A cylinder has diameter 16 inches and height 20 inches. A label covers the lateral surface area (the side) only. What is the area of the label?

When a label covers the side of a cylinder, its area is the lateral surface area, found by circumference times height. The radius is half the diameter, so r = 8 inches. The circumference is 2πr = 2π(8) = 16π inches. Multiply by the height, 20 inches, to get 16π × 20 = 320π square inches. The top and bottom circles aren’t included because the label sits only on the side. So the area is 320π square inches, which matches the given option.

A paper label wrapped around a can doesn’t cover the whole can. It covers the curved side, leaving the circular top and bottom untouched. That simple distinction matters when you calculate the label’s area: you need the cylinder’s lateral surface area, not its total surface area.

For a cylinder with a diameter of 16 inches and a height of 20 inches, the label covers 320π square inches. The result comes from a useful idea: if you cut the label down one side and lay it flat, it becomes a rectangle. One side of that rectangle is the cylinder’s height. The other is the distance around the cylinder, or its circumference.

A cylinder’s side becomes a rectangle

Picture peeling a label off a can. If it comes away cleanly, the curved sheet can lie flat on a table. Its shape is a rectangle, even though it hugged a round surface a moment ago.

That rectangle’s width matches the cylinder’s circumference. Its height matches the cylinder’s height. So the area of the side is:

Lateral surface area = circumference × height

A cylinder’s circumference is found with either of these familiar formulas:

  • C = πd, when you know the diameter

  • C = 2πr, when you know the radius

Here, d stands for diameter and r stands for radius. The radius is the distance from the center of a circular base to its edge. The diameter stretches all the way across the circle, through the center, so it is twice the radius.

For the can in this example, the diameter is 16 inches. Its circumference is:

C = πd = 16π inches

Now multiply by the height, 20 inches:

Lateral surface area = 16π × 20 = 320π square inches

The label’s area is therefore 320π square inches, or about 1,005.3 square inches if you use π ≈ 3.1416.

Why the top and bottom don’t count

A cylinder has three flat or curved surface regions to think about: one curved side and two circular bases. If you were measuring all the material needed to make a closed cylinder, you’d include every part. But a label that wraps around the side leaves the bases out.

That changes the formula. Total surface area includes the side and both circles:

Total surface area = 2πrh + 2πr²

The lateral surface area includes only the side:

Lateral surface area = 2πrh

Both formulas use the same radius and height, so it’s easy to mix them up. A quick sketch can help. Mark the curved side as one region, then shade the top and bottom circles only if they’re part of the surface being measured. In the label example, only the side gets shaded.

This distinction shows up in ordinary objects all the time. A printed sleeve around a jar may cover much of its side but not its lid or base. A metal can, meanwhile, needs material for its curved wall and for both ends. Same cylinder, different surface being measured.

Diameter or radius? Start with what you’re given

The label’s diameter is 16 inches, but the formula 2πrh uses the radius. That’s no trouble: the radius is half the diameter.

r = 16 ÷ 2 = 8 inches

Then:

2πrh = 2 × π × 8 × 20 = 320π square inches

This route gives the same result as using circumference first. The two methods are just different ways to organize the same calculation:

2πr × h = circumference × height

When the diameter is given, the formula πdh can be even quicker:

π × 16 × 20 = 320π square inches

It works because a circle’s circumference is also πd. Still, it’s worth knowing why the shortcut works. Formulas become easier to remember when they connect to a picture, rather than sitting in your mind as a string of symbols.

Keep the units in view

The circumference is measured in inches. The height is also measured in inches. Multiplying them gives square inches:

inches × inches = square inches

That unit check is a small but handy safeguard. A surface area should be measured in square units, such as square inches, square centimeters, or square feet. If a result ends in inches alone, something has gone sideways—perhaps a length was reported instead of an area.

The π form and the decimal form both describe the same area. 320π square inches is exact when the answer is left in terms of π. The decimal, about 1,005.3 square inches, is an approximation because π continues beyond the digits shown.

Which form should you use? It depends on the setting. An exact expression is compact and avoids rounding. A decimal can be easier to picture when estimating how much material a real label might need. For actual packaging, you’d also account for overlap, trimming, or a small gap; a clean geometry model doesn’t include those manufacturing details.

A couple of quick checks

Before settling on a result, it helps to ask whether its size makes sense. The circumference is 16π inches, or a little over 50 inches. Stretch that distance into a rectangle 20 inches tall, and you get an area a bit above 1,000 square inches. That feels reasonable: the label is wide and fairly tall.

You can also compare the answer with the total surface area. The radius is 8 inches, so each circular base has area π × 8² = 64π square inches. Both bases together add 128π square inches. The total surface area is therefore:

320π + 128π = 448π square inches

The side alone, 320π square inches, is less than the full surface area, as it should be. If a side-only calculation came out larger than the whole cylinder’s surface area, that would be a sign to revisit the numbers.

One more useful check: doubling the cylinder’s height doubles the label area, because the rectangular label becomes twice as tall. Doubling the diameter also doubles the circumference, and therefore doubles the lateral area if the height stays fixed. These relationships make the formula feel less mysterious. It’s simply the area of a rectangle whose width comes from the round shape.

The shape is doing the work

The most useful idea here isn’t just a formula. It’s the way the cylinder’s curved side unfolds into a rectangle. Once you see that, lateral surface area becomes a familiar calculation: width times height, with the circumference supplying the width.

For a cylinder with a 16-inch diameter and a 20-inch height, the circumference is 16π inches. Multiply by the 20-inch height, and the side area is 320π square inches, or about 1,005.3 square inches.

The next time you see a can, tube, or jar, imagine its label peeled away and spread flat. The geometry is hiding in plain sight.